DWG PRODUCT DIRECTIONS

DRI WASH ‘n GUARD® Waterless Carwash & Protective Glaze
It is extremely important that DRI WASH 'n GUARD® be applied with the AIRosol sprayer only. Use on hard, non-porous surfaces only. Pre-test on inconspicuous area before use. Can be used over surface containing moderate level of dust, dirt, road grime or salt.

Refill Procedures:

Directions By Hand:

1. Apply Dri Wash 'n Guard® to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
2. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
3. Invert the bottle and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap up and down until a strong resistance is felt (approx. 10-15 times).
5. Spray a generous coat of Dri Wash 'n Guard® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible. On windows, apply a light coat.
6. With moderately firm pressure, rub DWG thoroughly over the sprayed area until the filmy haze that appears almost disappears.
7. Buff the remaining haze to a high gloss with second terry cloth towel 

Directions by Machine:

1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 2,400 RPM.
2. Apply Dri Wash 'n Guard® as described in steps 3, 4, and 5 above.
3. Immediately buff sprayed area to a high gloss.
4. Continue, section by section, until all accessible areas have been buffed.
5. Polish any remaining areas by hand, if necessary. 

For ultimate surface restoration, use DRI WASH 'n GUARD® Oxygone
TM as Step 1, and DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze as Step 2.

DRI WASH ‘n GUARD® ULTRA-ION
TM Waterless Car Wash
It is extremely important that DRI WASH 'n GUARD® ULTRA-ION
be applied with a DRI WASH 'n GUARD® Car AIRosol pump sprayer only. Use on hard, non-porous surfaces only. Pre-test on inconspicuous area before use. Can be used over surface containing moderate level of dust, dirt, road grime or salt.


Refill Procedures:

Directions By Hand:

1. Apply Dri Wash 'n Guard® ULTRA-ION to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
2. Use two soft, clean terry cloth towels... one for applying the product and one for buffing. For best results, use the DWG Buffing Towel for buffing.
3. Invert the AIRosol pump sprayer and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap "up and down" until a strong resistance is felt (approx. 10-15 times).
5. Spray a light coat of Dri Wash 'n Guard® ULTRA-ION on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.
6. Using the terry cloth towel, with moderately firm pressure, rub polish thoroughly over the sprayed area until the filmy haze that developed almost disappears.
7. Buff the remaining haze to a high gloss with the DWG buffing towel 

Directions by Machine (FOR PROFESSIONALS ONLY):

1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 1,500 RPM.
2. Apply Dri Wash 'n Guard® ULTRA-ION as described in steps 3, 4, and 5 above.
3. Immediately buff sprayed area to a high gloss.
4. Continue, section by section, until all accessible areas have been buffed.
5. Polish any remaining areas by hand, if necessary. 

Caution: Use under well ventilated conditions. Prevent product from freezing. DO NOT MIX THIS PRODUCT WITH ANY OTHER CHEMICAL OR WATER. 


WASH ‘n GUARD® PowerBlast
Use on hard, non-porous surfaces only. Pre-test on inconspicuous area before use. Can be used over surface containing moderate level of dust, dirt, road grime or salt. This Product Contains No Harmful Propellants

Directions By Hand:

1. Invert Aerosol can and shake vigorously for 5 seconds.
2. Apply Dri Wash 'n Guard® to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
3. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
4. Spray a generous coat of Dri Wash 'n Guard® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible. On windows, apply a light coat.
5. With moderately firm pressure, rub DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze thoroughly over the sprayed area until the filmy haze that appears almost disappears.
6. Immediately buff the remaining haze to a high gloss with second terry cloth towel.
7. When finished, invert can and spray for 3 seconds to clear nozzle. 


DRI WASH ‘n GUARD® OxyGone
TM
For best results, pre-test on inconspicuous area before use.

Directions By Hand:

1. Invert bottle and shake vigorously for 5 seconds
2. Apply a small amount of OxyGone
TM on a clean terrycloth towel.
3. Using the towel, work the product into the oxidized surface until haze begins to disappear.
4. Using another clean terry cloth towel, buff the treated surface to a gloss.
5. For best results, work in small sections.

Directions by Machine:

1. Invert bottle and shake vigorously for 5 seconds.
2. To prevent splatter, apply a small amount of OxyGone
TM on a clean terrycloth towel and spread over a 12" area.
3. Buff to a high gloss using a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 2,400 RPM.


DRI WASH ‘n GUARD® Premium Metal Polish
DO NOT use on thin plated metal surfaces.
DO NOT use near heat, sparks, or flame.
DO NOT breath vapors for extended periods.
DO NOT mix this product with any other chemicals or liquids.
For best results, pre-test on inconspicuous area before use.

Directions:

1. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
2. Invert bottle and shake vigorously before and during use.
3. Apply a small amount of DRI WASH 'n GUARD® Premium Metal Polish on a clean terry cloth towel.
4. Rub surface lightly until polish turns dark.
5. Let dry and buff with a separate clean, terry cloth towel.
6. For maximum protection, apply DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze after treatment.



DRI WASH ‘n GUARD® Upholstery, Fabric and Carpet Treatment
DO NOT use on glass, floors, or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.
For best results, pre-test on inconspicuous area before use.

Directions:

1. Use one soft, clean terry cloth towel or soft bristle brush for cleaning, and another for drying
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 8-10 inches.
4. Agitate sprayed area with soft, clean, terry cloth towel or bristle brush.
5. Pat dry with soft, clean, terry cloth towel.
6. Allow area to completely dry.



DRI WASH ‘n GUARD® Leather and Vinyl Treatment
DRI WASH ‘n GUARD® Leather and Vinyl Treatment contains no petroleum distillates, soaps or detergents. It is non-corrosive, non-flammable, and non-caustic.
DO NOT use on glass, floors, woven materials or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.
For best results, pre-test on inconspicuous area before use.

Directions:

1. Use one soft, clean terry cloth towel or sponge for cleaning, and another for buffing.
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 8-10 inches. To prevent overspray, apply to an area no larger than 18 inches.
4. Rub sprayed area with a soft, clean terry cloth towel or sponge. (For excessively soiled areas, scrub lightly with a soft brush and then rub with a clean soft terry cloth towel or sponge.)
5. For best results, buff lightly with a clean, terry cloth towel. 

DRI WASH ‘n GUARD® All Weather Tire Treatment
DO NOT use on glass, Plexiglas, mirrors, chrome or other non-porous surfaces.
DO NOT use in an area where painting occurs or on surfaces that may require painting.
DO NOT mix this product with any other chemicals or liquids.
First: Replace shipping cap with trigger sprayer (included).

Directions:

1. Use one soft, clean cloth for cleaning/polishing and another for buffing.
2. Invert bottle and shake once.
3. Rotate nozzle to "SPRAY" position.
4. Spray generously onto surface from a distance of approximately 8-10 inches.
5. Immediately polish the are with a soft, clean cloth. The use of a small, soft bristle brush may be helpful in penetrating rough or uneven surfaces such as tire sidewalls.
6. Buff to a shine using a second soft, clean cloth.
7. Repeat process for higher luster and longer lasting protection.


DRI WASH ‘n GUARD® Oil Treatment
Recommended Usage: Change oil every 3000 - 4000 miles.
Passenger Vehicles: Use 8 ounces or contents of one bottle.
Diesel Engines including Semi-Tractors: Use one ounce per quart of oil.
NO NEED TO CHANGE OIL PRIOR TO FIRST TIME USE.

Directions:

Shake bottle vigorously for 10 seconds before adding. Add above recommended quantities to engine crankcase.


DRI WASH ‘n GUARD® Dust B' Gone
TM
DO NOT use on glass, Plexiglas, mirrors, chrome or other extremely porous surfaces.
DO NOT use in an area where painting occurs or on surfaces that may require painting.
DO NOT mix this product with any other chemicals or liquids.

Directions:

1. Test in a discrete area before general use.
2. Invert bottle and shale once.
3. Spray onto surface from approximately 10 inches away.
4. Some surfaces may require immediate polishing with a soft clean cloth.
5. Heavy dust build-up may require a second application.


DRI WASH ‘n GUARD® For The Home
DO NOT use on chrome-coated plastic or vinyl flooring.
DO NOT use on vehicle exteriors. Painted surfaces treated with the product may discolor when exposed to outdoor sunlight.

Tips:
No need to "pre-clean" surfaces before using DRI WASH ‘n GUARD® For The Home. Let our product do the cleaning for you! Surfaces must be completely dry before applying. Between applications, wipe with a damp terry cloth towel and buff with a dry terry cloth towel.

Directions:

1. Invert aerosol can and shake vigorously.
2. Use two soft, clean terry cloth towels... one for cleaning/polishing, and one for buffing.
3. Spray a light coat of DRI WASH ‘n GUARD® For The Home directly onto dry surface.
4. With moderate firm pressure, rub polish thoroughly over the sprayed area until the filmy haze that develops almost totally disappears.
5. Immediately buff remaining haze to a high gloss with second terry cloth towel.